ERROR CODES | EXAPTATION |
---|---|
0122 | CAN bus overload |
0123 | Functional failure of the CAN data bus |
0132 | The life cycle data of the WS control unit is incorrect. |
0133 | The parameters of the WS control unit are incorrect. |
0135 | Internal error in the control unit |
0138 | Internal error in the control unit |
0139 | Internal error in the control unit |
0150 | Waiting time for receiving CAN data BU ABS |
0151 | Waiting time for receiving CAN data BU GS |
0152 | Waiting time for receiving CAN data BU FR |
0153 | Waiting time for receiving CAN data CAN data reception BU MR |
0154 | Waiting time for CAN data reception BU RS |
0155 | Waiting time for CAN data reception BU FR |
0156 | Waiting time for CAN data reception BU MR |
0157 | Waiting time for receiving CAN data BU INS |
0158 | Waiting time for receiving CAN data BU BS |
0159 | Waiting time for receiving CAN data BU GS |
0201 | Gearbox oil temperature sensor has a fault "Short circuit to ground". |
0202 | The measurement range of the gearbox oil temperature sensor has been exceeded. |
0205 | The measured value of the gearbox oil temperature sensor is unreliable. |
0210 | The maximum allowable gearbox oil temperature has been exceeded. |
0301 | The transfer case temperature sensor has a "Short to Ground" fault. |
0302 | The measurement range of the transfer case temperature sensor has been exceeded. |
0305 | The measured value of the transfer case temperature sensor is unreliable. |
0310 | The maximum allowable transfer case oil temperature has been exceeded. |
0401 | The front axle temperature sensor has a "Short to Ground" fault. |
0402 | Front axle temperature sensor measurement range exceeded. |
0405 | The measured value of the front axle temperature sensor is unreliable. |
0410 | The maximum allowable oil temperature of the front axle gearbox has been exceeded. |
0501 | The rear axle temperature sensor has a "Short to Ground" fault. |
0502 | The measurement range of the rear axle temperature sensor has been exceeded. |
0505 | The measured value of the rear axle temperature sensor is unreliable. |
0510 | The maximum permissible oil temperature of the rear axle gearbox has been exceeded. |
0601 | The condensed liquid sensor has a "Short Circuit" to ground fault. |
0604 | The condensed liquid sensor has an "Open Circuit" fault. |
0605 | Invalid measured value of the condensate sensor. |
1011 | Too much difference in brake pad wear between the brakes of the 1st front axle. |
1012 | Too much difference in brake pad wear between the 1st front axle and other axles. |
1111 | Too much difference in brake pad wear between the brakes of the 2nd front axle. |
1112 | Too much difference in brake pad wear between the 2nd front axle and other axles. |
1211 | Too much brake pad wear difference between the brakes of the 1st rear axle. |
1212 | Too much difference in brake pad wear between the 1st rear axle and other axles. |
1311 | Too much difference in brake pad wear between the brakes of the 2nd rear axle. |
1312 | Too much difference in brake pad wear between the 2nd rear axle and other axles. |
1401 | Short circuit of the signal wire of the left brake pad wear sensor of the 1st front axle. |
1402 | The measured wear value of the brake pads of the 1st front axle on the left is above the measuring range. |
1403 | The measured value of the wear of the brake pads of the 1st front axle on the left is below the measuring range. |
1404 | Breakage of the signal wire of the left brake pad wear sensor of the 1st front axle. |
1405 | Invalid measured wear of the brake pads of the 1st front axle on the left. |
1420 | Failure of the CAN signal for wear of the brake pads of the 1st front axle on the left |
1501 | Short circuit of the signal wire of the right brake pad wear sensor of the 1st front axle. |
1502 | The measured wear value of the brake pads of the 1st front axle on the right is above the measurement range. |
1503 | The measured wear value of the brake pads of the 1st front axle on the right is below the measurement range. |
1504 | Breakage of the signal wire of the right brake pad wear sensor of the 1st front axle. |
1505 | Invalid measured wear value of the brake pads of the 1st front axle on the right. |
1520 | Failure of the CAN signal for wear of the brake pads of the 1st front axle on the right |
1601 | Short circuit of the signal wire of the left brake pad wear sensor of the 2nd front axle. |
1602 | The measured wear value of the brake pads of the 2nd front axle on the left is above the measurement range. |
1603 | The measured value of the wear of the brake pads of the 2nd front axle on the left is below the measuring range. |
1604 | Breakage of the signal wire of the left brake pad wear sensor of the 2nd front axle. |
1605 | Invalid measured wear of the brake pads of the 2nd front axle on the left. |
1620 | Failure of the CAN signal for wear of the brake pads of the 2nd front axle on the left |
1701 | Short circuit of the signal wire of the right brake pad wear sensor of the 2nd front axle. |
1702 | The measured wear value of the brake pads of the 2nd front axle on the right is above the measuring range. |
1703 | The measured wear value of the brake pads of the 2nd front axle on the right is below the measuring range. |
1704 | Breakage of the signal wire of the right brake pad wear sensor of the 2nd front axle. |
1705 | Invalid measured wear value of the brake pads of the 2nd front axle on the right. |
1720 | Failure of the CAN signal for brake pad wear of the 2nd front axle on the right |
1801 | Short circuit of the signal wire of the left brake pad wear sensor of the 1st rear axle. |
1802 | The measured wear value of the brake pads of the 1st rear axle on the left is above the measuring range. |
1803 | The measured wear value of the brake pads of the 1st rear axle on the left is below the measuring range. |
1804 | Breakage of the signal wire of the left brake pad wear sensor of the 1st rear axle. |
1805 | Unreliable measured wear value of the brake pads of the 1st rear axle on the left. |
1820 | Failure of the CAN signal for wear of the brake pads of the 1st rear axle on the left |
1901 | Short circuit of the signal wire of the right brake pad wear sensor of the 1st rear axle. |
1902 | The measured wear value of the brake pads of the 1st rear axle on the right is above the measurement range. |
1903 | The measured wear value of the brake pads of the 1st rear axle on the right is below the measuring range. |
1904 | Breakage of the signal wire of the right brake pad wear sensor of the 1st rear axle. |
1905 | Unreliable measured wear value of the brake pads of the 1st rear axle on the right. |
1920 | Failure of the CAN signal for wear of the brake pads of the 1st rear axle on the right . |
2001 | Short circuit of the signal wire of the left brake pad wear sensor of the 2nd rear axle. |
2002 | The measured value of the wear of the brake pads of the 2nd rear axle on the left is above the measuring range. |
2003 | The measured value of the wear of the brake pads of the 2nd rear axle on the left is below the measuring range. |
2004 | Breakage of the signal wire of the left brake pad wear sensor of the 2nd rear axle. |
2005 | Unreliable measured wear value of the brake pads of the 2nd rear axle on the left. |
2020 | Failure of the CAN signal for wear of the brake pads of the 2nd rear axle on the left |
2101 | Short circuit of the signal wire of the right brake pad wear sensor of the 2nd rear axle. |
2102 | The measured wear value of the brake pads of the 2nd rear axle on the right is above the measuring range. |
2103 | The measured wear value of the brake pads of the 2nd rear axle on the right is below the measuring range. |
2104 | Breakage of the signal wire of the right brake pad wear sensor of the 2nd rear axle. |
2105 | Invalid measured wear of the brake pads of the 2nd rear axle on the right. |
2120 | Failure of the CAN signal for wear of the brake pads of the 2nd rear axle on the right |
2205 | Invalid measured value (path signal) of the tachograph. |
2320 | Failure of the CAN signal 'Residual pressure circuit 1 or 2' (INS) |
3105 | Invalid speed signal SZ. |
3120 | Failure of the SZ speed signal on CAN |
3220 | Failure of the speed signal on CAN |
3320 | Failure of the engine torque setpoint signal on CAN |
3420 | Failure of the outside air temperature measured value signal on CAN |
3520 | Failure measured value CAN signal dirty air filter |
4105 | Invalid measured oil temperature in the retarder (retarder). |
4110 | The maximum allowable oil temperature in the retarder (retarder) has been exceeded. |
4120 | Failure of the CAN signal of the measured value of the oil temperature in the retarder (retarder) |
5105 | Invalid measured value of the oil temperature in the engine. |
5110 | The maximum allowable oil temperature in the engine has been exceeded. |
5113 | Incorrect engine oil viscosity. |
5120 | Failure of the CAN signal of the measured oil temperature in the engine |
5205 | Invalid measured value of the coolant temperature. |
5210 | The maximum allowable coolant temperature has been exceeded. |
5220 | CAN signal failure of measured coolant temperature value |
5320 | CAN signal failure of fuel consumption measured value |
7120 | CAN signal failure of clutch actual value |
Attention!: using adblue remove emulator is illegal in specially EN countries.Using this device causes elevated exhaus gas emission. When you started use adblue remove emulator, your truck doesnt comply with the euro4, euro5 and euro6 standards. Our device for countries that havent euro 4/5/6 ecologic rules. Adblue remove emulator, stoped the DEF liquid flowing in scr system. Adblue remove emulator sell for countries that havent adblue liquid and use for during the remove faults in adblue systems. This is a personal decision to buy this device. Our company doesnt resposible in any legal problems that groves with this decision.
Sail Tech Ltd Adblue Removal Emulator
Typically replies within an hourHow can i help you?